콘크리트 모듈러 도로 축하중 거동 분석을 통한 설계 타당성 검증
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국도로학회
ㆍ수록지정보 : 한국도로학회논문집 / 17권 / 6호
ㆍ저자명 : 남정희, 김우석, 김기현, 김연복
ㆍ저자명 : 남정희, 김우석, 김기현, 김연복
목차
1. 서론2. 콘크리트 모듈러 도로 구조설계
3. 콘크리트 모듈러 도로 Mock-up 시공
4. 축하중 실험을 통한 설계 타당성 분석
5. 결론
감사의 글
REFERENCES
영어 초록
PURPOSES: The purpose of this study is to validate the design criteria of the concrete modular road system, which is a new semi-bridgetype concept road, through a comparison of numerical analysis results and actual loading test results under static axial loads.METHODS : To design the semi-bridge-type modular road, both the bridge design code and the concrete structural design code were adopted. The standard truck load (KL-510) was applied as the major traffic vehicle for the design loading condition. The dimension of the modular slab was designed in consideration of self-weight, axial load, environmental load, and combined loads, with ultimate limit state coefficients. The ANSYS APDL (2010) program was used for case studies of center and edge loading, and the analysis results were compared with the actual mock-up test results.
RESULTS : A full-scale mock-up test was successfully conducted. The maximum longitudinal steel strains were measured as about 35 and 83.5 micro-strain (within elastic range) at center and edge loading locations, respectively, under a 100 kN dual- wheel loading condition by accelerating pavement tester.
CONCLUSIONS: Based on the results of the comparison between the numerical analysis and the full-scale test, the maximum converted stress range at the edge location is 32~51% of the required standard flexural strength under the two times over-weight loading condition. In the case of edge loading, the maximum converted stresses from the Westergaard equation, the ANSYS APDL analysis, and the mock-up test are 1.95, 1.7, and 2.3 times of that of the center loading case, respectively. The primary reason for this difference is related to the assumption of the boundary conditions of the vertical connection between the slab module and the crossbeam module. Even though more research is required to fully define the boundary conditions, the proposed design criteria for the concrete modular road finally seems to be reasonable.
참고 자료
없음태그
"한국도로학회논문집"의 다른 논문
- 실 규모 터널 주행실험을 통한 터널 경계부 휘도 기준의 적정성 검증11페이지
- 도로전광표지를 이용한 국도우회정보 제공이 고속도로 운영에 미치는 효과 분석 -영동고속도로를 중심으로..8페이지
- 고속도로 오르막차로 교통사고 심각도 영향요인 분석11페이지
- 존별 특성을 반영한 교통사고밀도 모형 - 청주시 사례를 중심으로 -9페이지
- Random Parameter를 이용한 4지 신호교차로에서의 교통사고 예측모형 개발 : 부산광역시를..9페이지
- Laboratory Performance Evaluation of Recycled Asphalt B..9페이지
- 표면 에너지 원리를 이용한 칩실 포장의 초기 점착력 특성 연구8페이지
- 차량 이동궤적 기반 버스정차대 기하구조 연구4페이지
- 터널천단변위와 암석 또는 암반의 일축압축강도를 이용한 시공 중인 터널의 예비 안정성 평가6페이지
- 무기계 바인더를 이용한 탄소저감형 흙포장의 성능평가8페이지