매크로 요소를 사용한 판형교 바닥판의 휨거동 해석
* 본 문서는 배포용으로 복사 및 편집이 불가합니다.
서지정보
ㆍ발행기관 : 한국전산구조공학회
ㆍ수록지정보 : 한국전산구조공학회 논문집 / 13권 / 1호
ㆍ저자명 : 최진유, 양기재, 박남회, 강영종
ㆍ저자명 : 최진유, 양기재, 박남회, 강영종
한국어 초록
교량 바닥판 설계에 대한 현 시방규정은 바닥판 슬래브가 처짐이 구속된 거더에 연속 지지되어 있다고 가정하므로, 바닥판 지간 중앙의 정모멘트와 거더 상단에 발생하는 부모멘트의 크기가 같은 것으로 간주하고 있다. 그러나 바닥판에 발생하는 휨모멘트는 거더의 처짐에 의해서 많은 영향을 받고 있으며, 거더의 처짐을 고려치 않는 현 시방규정에 의해 설계된 바닥판은 상부철근의 부식으로 인한 내구성 저하와 유지보수 비용 증가 등의 문제점을 안고 있다. 따라서 본 연구에서는 매크로 요소를 이용해 거더의 처짐 효과를 고려할 수 있는 해석법을 개발하였고, 이를 유한요소법을 통해 검증하였다. 또한, 이 해석법을 바탕으로 바닥판의 횡방향 휨모멘트에 영향을 미치는 여러 변수에 대한 분석을 수행하였다. 해석 결과, 바닥판의 지점부 모멘트는 거더의 간격뿐만 아니라 거더와 바닥판의 휨강성비 교량의 길이, 하중의 재하위치, 거더의 비틀림 강성, 가로보의 휨강성과 배치 간격 등에 많은 영향을 받고 있는 것을 알 수 있으며, 영향선을 이용해 최대하중 위치를 결정하여 몇 개의 예제교량을 대상으로 지점부의 설계모멘트를 계산해 본 결과, 현 시방규정이 다소 보수적인 값을 나타내고 있다.영어 초록
Current specification prescribes that upper and lower reinforcement mat is required in the same amount to resist negative and positive moment in bridge decks. But the negative moment is much smaller than positive moment because the actual behavior of decks consists of local deflection of slab and global deflection of girder. From this study, the analysis method based on harmonic analysis and slope-deflection method was developed and verified by finite element method. The negative moment, obtained from this method, were smaller than those computed based on the KHBDC specifications as much as 4050% in the middle of bridge. The amount of reduction of the design negative moment was shown herein to be dependent on variable parameters as shape factor(S/L) of slab, relative stiffness ratio of girder and deck slab, and so on. This investigations indicate that the upper reinforcement mat to resist negative moment can be removed. But further experimental study is required to consider durability and serviceability. From this new design concept, the construction expense can be reduced and the problem of decreasing durability resulting from corrosion of upper reinforcement steel settled.참고 자료
없음태그
"한국전산구조공학회 논문집"의 다른 논문
- 철근콘크리트 냉각탑의 형상불완전에 의한 확률론적 거동12페이지
- STEP을 이용한 철골건물의 구조설계정보 통합시스템의 구축에 관한 연구8페이지
- Nonlinear Random Vibration of Laminated Composite Plate..10페이지
- 건물 구조 통합 구조설계 시스템의 구현을 위한 설계 객체 모델13페이지
- 3차원 비정형 Setback 구조물의 지진 거동9페이지
- 칩과 리드페임의 접착과정에서 발생하는 잔류 응력 해석7페이지
- 유한요소법을 이용한 정현상으로 taper진 부재의 고유치 산정9페이지
- 부분적 측정데이타를 이용한 구조시스템의 동적응답 추정기법11페이지
- 일본의 기존 철근콘트리트건물의 내진성능 및 지진피해율의 평가12페이지
- The Finite Element Analysis for Calculations of Equival..12페이지