[네트워크]DataCommunication and Networking (forouzan)
- 최초 등록일
- 2006.06.18
- 최종 저작일
- 2006.06
- 4페이지/ 한컴오피스
- 가격 2,000원
소개글
DataCommunication and Networking (forouzan)
chapter 14.
review questions / Exercises 정답
목차
1. How is the peramble field different from the SFD field?
2. What is the purpose of an NIC?
3. What is the purpose of a trancceiver?
4. What is the difference between a multicast address and a broadcast address?
5. What are the advantages of dividing an Ethernet LAN with a bridge?
6. What is the relationship between a switch and bridge?
7. Why is there no need for CSMA/CD on a full-duplex Ethernet LAN?
8. Compare the data rats for traditional Ethernet, fast Ethernet and Gigabit Ethernet?
9. What are the common traditional Ethernet implementation?
10. What are the common fast ethernet implementation?
11. What are the common Gigabit ethernet implementation?
12. What is the purpose of autonegotiation?
13. Compare the reconciliation sublayer in fast Ethernet with the PLS sublayer in traditional Ethernet.
14. What is the GMII in Gigabit Ethernet?
15. What Internet model layers are of concern to LANs?
Exercise
31. What is the radio of useful data to the entire packet for the smallest Ethernet frame? what is the ratio for the largest frame? What is average ratio?
33. Imagine the length of a 10Base5 cable is 2500m. if the speed of propagation in a thick coaxial cable is 200,000,000 m/s, how long dose it take for a bit to travel form the beginning to the end of the network? Ignore any propagation delay in the equipment.
35. An Ethernet MAC sublayer receives 42 byte of data from the LLC sublayer. How many bytes of padding must be added to the data?
37. Complete table 14.1
39. Compare the different Fast Ethernet implementations using Table 14.3.
본문내용
1. How is the peramble field different from the SFD field?
프리앰블은 802.3프레임의 첫 번째 필드로서 0과 1을 반복하는 7바이트(56비트)를 포함하고, 수신 시스템에게 프레임이 도착하는 것을 알려주며, 입력 타이밍에 수신 시스템이 동기화할 수 있도록 만든다.
SFD는 프레임의 시작을 알린다. SFD는 두 번째 필드이며 1바이트(10101011)이다.
마지막 2비트는 11이며 수신자에게 이 다음 필드가 목적지 주소임을 알려준다.
2. What is the purpose of an NIC?
NIC(network Interface Card) : Station 내부에 설치되어 있고 6바이트의 물리적 주소를 Station 에 제공한다.
NIC은 네트웍에 접속할 수 있게 하기 위해 컴퓨터 내에 설치되는 확장 카드이다. 근거리통신망에 연결된 PC나 워크스테이션들은 대체로 이더넷이나 토큰링과 같은 근거리통신망 전송기술을 위해 특별히 설계된 네트웍 카드를 장착하고 있다.
네트웍 카드는 컴퓨터가 네트웍에 상시 접속되도록 해준다. 그러나, 대부분의 가정이나 휴대용 컴퓨터들은 필요할 때마다 다이얼업으로 인터넷에 접속하며, 이때에는 모뎀을 통해 인터넷 서비스 공급자와 연결된다.
3. What is the purpose of a trancceiver?
매체를 통해 신호를 전송하고 매체를 통해 신호를 받는다. 또한 충돌을 감지한다.
고속 이더넷의 송수신기는 PHY계층이다. 10-Mbps 이더넷의 정규 기능을 유지하면서 고속 이더넷의 송수신기는 부호화와 복호화를 위한 책임을 진다.
참고 자료
없음